Gap under a sauna door
Gap under a sauna door is the clear opening between a closed door leaf and the finished floor or threshold. In some designs it is a transfer-air terminal; in others it has no assigned ventilation function. Its flow depends on clear geometry, pressure difference and the connected paths on both sides. A door undercut is therefore neither a complete ventilation system nor necessarily a source of outdoor air, and no single height is suitable for every sauna or doorset.[1]
Geometry and flow
For a simple rectangular opening, gross area is approximately clear width multiplied by clear height. Effective area is smaller and more complex because the door edge, threshold profile, floor unevenness, seals, sweeps and nearby surfaces cause contraction and resistance. A later mat, threshold or floor finish can materially reduce the installed opening. Recording a nominal “gap” without its width, threshold and minimum clear height is consequently ambiguous.
Flow occurs only when pressure differs across the Sauna door. Wind, indoor–outdoor temperature difference, fans, chimney draught and the operation of other doors can all change this pressure. The same opening can carry air into the hot room in one state and out of it in another. A larger undercut lowers one part of the path's resistance but does not itself supply more outside air; the adjoining room must have a suitable upstream or downstream connection.[2]
Local velocity at one point cannot be converted directly into air changes per hour. Flow must be integrated over the effective opening and related to a declared room volume, while other leakage and terminals remain part of the mass balance. Opening the whole door creates a much larger, transient and often two-way exchange and is not equivalent to flow beneath a closed leaf.
Function in ventilation systems
Within Sauna ventilation, an undercut can transfer air between a sauna and a washroom. If an extract fan depressurises the washroom, the gap may serve as the sauna's outward transfer route. If the sauna is more negative, it may instead act as an inward Sauna air inlet. Under Natural sauna ventilation, weather and stack pressure can alter direction; in Mechanical sauna ventilation, other fans and damper states remain relevant. The label “inlet” or “outlet” should therefore describe the designed or observed function in a stated mode.
Even a verified transfer flow does not demonstrate good distribution at the benches. Floor-level air may remain in a cool lower zone, mix into the heater plume or pass rapidly to another terminal. Enlarging the opening can also change flows through a dedicated Sauna air outlet and through leakage. The outcome must be assessed within the whole pressure route and occupied-zone conditions, not from free area alone.[1]
Product-specific examples
Harvia's current general guidance specifies an under-door gap of at least 100 mm in one arrangement where the sauna transfers air to a washroom containing mechanical exhaust.[3] The same condition appears in the PC110EE/PC110HEE heater instructions: the dimension is tied to an outlet in the washroom and mandatory mechanical extraction in that arrangement.[4] Saunum uses the same 100 mm value for its Professional climate unit when the air outlet is in the shower room.[5] These matching manufacturer instructions are not an independent scientific consensus or a universal building-code rule.
Tylö's guide describes a different product concept. It allows under-door supply in a particular layout where the heater is close to the door, but recommends direct supply below the heater and a return to the same adjoining pressure space for its self-draught route.[6] The examples should not be blended. Gap size and purpose must follow the actual heater, ventilation and door documentation.
The principal VTT sauna-airflow experiment varied opening positions in a mechanically exhausted room, but did not test a controlled series of door-gap dimensions.[7] It supports the importance of the whole opening arrangement, not a particular undercut.
Door, access and fire constraints
The opening belongs to a complete doorset. Clear opening width, swing direction, hinges, latching and the Sauna door handle affect circulation and emergency use. A raised threshold can contain water or reduce draught but create a movement barrier. A Glass sauna door or prefabricated door can have supplied clearances integral to its assembly. These matters require coordinated Sauna design rather than selection from airflow considerations alone.
Accessibility requirements vary by facility and jurisdiction. Under United States federal accessibility standards, covered saunas and steam rooms require turning space, an accessible bench where seating is provided, compliant user controls and door manoeuvring provisions; thresholds are also constrained. The Access Board's sauna guide does not prescribe a ventilation undercut.[8] ISO 21542:2021 addresses accessibility and usability of buildings more broadly and supplies no sauna-gap value in its public scope. At the research cut-off, its 2026 systematic review had closed on 3 September and the ISO record had not yet displayed a final confirmation or revision decision.[9]
A fire- or smoke-resisting door depends on its tested or approved doorset, including required perimeter gaps and seals. It should not be trimmed, drilled or stripped of a seal to create ventilation without evidence that the altered assembly remains acceptable. England's Approved Document B is statutory guidance for fire safety in England, while Approved Document M addresses access and use there; neither establishes a worldwide sauna-door value.[10] Any alteration must be reconciled with the applicable authority, certification and egress design.
Wet and exposed locations
Cleaning water, floor falls and splash interact with a floor-level opening. A sweep fitted later may obstruct the designed air path; an enlarged gap may reduce privacy, acoustic separation and water containment. No checked evidence supplies a universal compromise among these functions.
On an Outdoor sauna, an external undercut can admit insects, wind-driven rain, snow and very cold air. Winter temperature differences may increase stack pressure, but wind, fans and a chimney can still reverse direction. Weather detailing and winter operation are site-specific. Whether alteration needs building or planning approval is jurisdiction-dependent; the existence of a ventilation gap creates no exemption.
Inspection, measurement and alteration
ISO 16956:2015 covers field airflow measurement at ducts and terminals under steady conditions, but is not a dedicated method for irregular door gaps. ISO 12569:2017 can estimate single-zone exchange under stated tracer-gas conditions. ISO 9972:2015 measures enclosure permeability under imposed pressure and expressly does not evaluate individual components.[11] A capture device can disturb the small pressure driving an undercut, while a tracer result includes other openings and leakage.
A survey should record clear height along the full width, threshold and floor geometry, seals, leaf position, adjoining pressures, fan states, heater and chimney condition. Blocking the gap can change pressure, air quality and combustion behaviour; enlarging it can compromise the doorset or another ventilation mode.[12] Diagnosis should compare the intended drawing with the installation before any modification, and distinguish observed direction from assumed purpose.
Changes in use should prompt the same comparison. A replacement door, new floor covering, added seal, modified washroom extract or changed heater can make the original undercut calculation inapplicable. Deposits or swelling may also reduce clearance unevenly, while a warped leaf can create a misleading large opening at one edge. A local high-velocity draught is not proof of adequate total exchange, and the absence of a noticeable draught is not proof of zero flow. If a temporary obstruction is removed during testing, the doorset should be restored to its approved condition afterwards. Permanent cutting or removal of seals should wait until ventilation intent, fire performance, accessibility and the manufacturer's documentation have been reconciled by the responsible parties.
See also
References
- ↑ 1.0 1.1 ASHRAE, “Ventilation and Infiltration”, chapter 16, 2025 ASHRAE Handbook—Fundamentals, 2025, official online chapter, accessed 5 September 2026.
- ↑ Finland, Ministry of the Environment, Decree 1009/2017 on the Indoor Climate and Ventilation of New Buildings, issued 20 December 2017, sections 1, 2, 8, 15, 17, 21–22 and 27, Finlex record, accessed 5 September 2026.
- ↑ Harvia, “Ventilation in the sauna”, updated 29 January 2026, official support page, accessed 5 September 2026.
- ↑ Harvia, PC110EE/PC110HEE Installation and Use Instructions, section 2.2 “Sauna room ventilation”, current hosted edition, official PDF, accessed 5 September 2026.
- ↑ Saunum, Professional Installation Manual, section “Sauna room ventilation”, current hosted edition, official PDF, accessed 5 September 2026.
- ↑ Tylö, Guide — How to build a sauna, current hosted edition, pp. 4–5, official PDF, accessed 5 September 2026.
- ↑ Erkki Äikäs and Rolf Holmberg, Saunan lämpötilat ja ilmanvaihto [Temperature and ventilation of the Finnish sauna], VTT Research Notes 1431, VTT, Espoo, 1992, 40 pp., ISBN 951-38-4325-4, official record, accessed 5 September 2026.
- ↑ United States Access Board, Chapter 6: Saunas and Steam Rooms, September 2021, official guide, accessed 5 September 2026.
- ↑ International Organization for Standardization, ISO 21542:2021, Building construction — Accessibility and usability of the built environment, edition 2, 2021, official record, accessed 5 September 2026.
- ↑ UK Government, Approved Document B: Fire safety, publication page updated 11 March 2025, official page, and Approved Document M: Access to and use of buildings, publication page updated 1 October 2024, official page, accessed 5 September 2026.
- ↑ International Organization for Standardization, ISO 16956:2015, Thermal performance in the built environment — Determination of air flow rate in building applications by field measuring methods, edition 1, confirmed 2025, official record; ISO 12569:2017, Thermal performance of buildings and materials — Determination of specific airflow rate in buildings — Tracer gas dilution method, edition 3, confirmed 2024, official record; and ISO 9972:2015, Thermal performance of buildings — Determination of air permeability of buildings — Fan pressurization method, edition 3, confirmed July 2026, official record, all accessed 5 September 2026.
- ↑ Tina Chen, “Rapid review: Environmental health risks and safety considerations in saunas”, National Collaborating Centre for Environmental Health, 16 January 2026, official evidence brief, accessed 5 September 2026.
