Jump to content

Temperature measurement in a sauna

From RUVARO Sauna Wiki

Temperature measurement in a sauna is the planned determination of a defined thermal quantity at stated places and times in a sauna room. A defensible result identifies the measurand, instrument and measuring chain, coordinates, operating phase, calibration and uncertainty. These qualifications matter because Sauna temperature varies with height, horizontal position and time; one unlocated reading cannot represent the complete Sauna climate. ISO 7726:2025 frames thermal-environment measurement in terms of specified physical quantities and instrument characteristics rather than a generic temperature number.[1]

Routine indication, appliance control and quantitative investigation have different aims. A Sauna thermometer can help reproduce use at its own location. A heater’s Sauna temperature sensor regulates or protects equipment. A comparative study or commissioning survey may instead require several characterised channels. Similar-looking displays do not make these measurements equivalent.

Choosing the measurand

Air, surface and mean radiant temperature are separate quantities. An air probe exchanges heat with its local surroundings; a contact sensor concerns a specified surface; mean radiant temperature represents the radiative environment. A globe thermometer responds to both convection and radiation and cannot be reported as ordinary dry-bulb air temperature without an appropriate model.[2] Thermal imaging of a sauna maps surface-associated radiance, not local air temperature.

Section of a sauna with six numbered symbols: an air probe near the bench, a wall thermometer, a sensor near the heater, contact probes on surfaces, a globe thermometer and a seated figure.
Choosing the measurand. Air temperature at a point, a wall thermometer indication, a heater control sensor, surface temperatures, mean radiant temperature and body temperatures are separate quantities that need separate methods. Schematic.

Sauna-specific research illustrates why the distinction matters. Ishibashi and colleagues found measured mean radiant temperature below air temperature in their particular setting; a model that included absorption by water vapour and carbon dioxide agreed better than a transparent-gas model.[3] This is evidence for separate quantities, not a fixed offset for other rooms.

Environmental temperatures must also be distinguished from Skin temperature and Core body temperature, including the methods covered by Core temperature measurement in a sauna. Room conditions contribute to heat exchange but are not direct readings of thermoregulatory response or heat strain. A measurement question—warm-up, occupied-zone distribution, heater cycling, a water-on-stones transient or surface assessment—determines which quantity is needed.

Instruments and measuring chains

Platinum resistance thermometers and thermocouples are common in logged measurements. IEC 60751:2022 specifies requirements and a resistance–temperature relationship for industrial platinum resistance thermometers and sensors.[4] It does not make a complete channel accurate merely because it contains a Pt100 or Pt1000 element. Lead resistance, excitation, self-heating, immersion, probe construction and readout remain relevant; the BIPM guide to industrial platinum resistance thermometers discusses these as system properties.[5]

A thermocouple produces an electromotive force related to the temperature difference between measuring and reference junctions. IEC 60584-1:2013 supplies reference functions and tolerances for designated types, but not an uncertainty certificate for the installed junction, extension cable, reference-junction treatment and logger.[6] A small exposed junction may respond rapidly but can be more affected by radiation, wetting, damage or electrical interference. Instrument choice is therefore a trade-off rather than a ranking by sensor name.

Probe, lead, connector and recorder may have different environmental ratings. Locating electronics outside the hot room can protect the recorder, while the connecting lead and feed-through remain part of the channel. A control or protective sensor is an equipment component, not a moveable room-mapping probe; altering it would be an appliance intervention governed by the identified equipment documentation.

Spatial and temporal sampling

Heater-driven buoyancy, enclosure temperatures and ventilation commonly create vertical stratification. Horizontal differences may also occur near the heater, door, glazing, walls and supply or extract openings. VTT experiments found position- and ventilation-dependent distributions in specified Finnish test saunas.[7] Fan, Holmberg and Heikkinen likewise found inlet-position sensitivity in one computational room model.[8] Neither study defines a universal sensor coordinate.

A multi-height array can resolve stratification better than one wall point, but reproducibility requires horizontal coordinates relative to heater, benches, envelope and vents. If positions are intended to represent bathers, the report should state posture or body level without equating air temperature with body exposure. Channel offsets should be checked before small differences are interpreted as spatial gradients.

Front-view outline of a sauna room with six paired sensor symbols in two rows, labelled 0.90 metres and 1.73 metres, and three columns labelled left, middle and right.
A purpose-specific array from one 2026 study: six thermocouples paired with six humidity sensors at three horizontal locations and two heights. It is an example of a multi-height array, not a prescribed layout. Schematic, not to scale.

Laatikainen-Raussi and colleagues used six K-type thermocouple cords and six analogue humidity sensors at three horizontal locations and two heights during participant-controlled Finnish-sauna sessions.[9] This was one purpose-specific array, not a prescribed layout, and humidity was not independently randomised. Coordinated Humidity measurement in a sauna can aid interpretation, provided clocks and locations are aligned.

Sampling interval and physical response are different. Fast logging cannot make a slow probe follow a rapid change; slow sampling can miss heater cycling or a brief water-casting event even when the element responds quickly. Any averaging or filtering should be reported. Time synchronisation is especially important when temperature is compared with humidity or physiological signals.

Interaction between sensor and environment

Probe on a short stem between a hot stone bed and a cool glass pane, with labelled arrows for convection, radiation, conduction along the stem and droplets on the tip.
An air-temperature sensor also exchanges heat by radiation with hot stones or cool glazing and by conduction along its stem, and it can be wetted after water is cast. A shield reduces radiation but changes airflow and response. Schematic.

An air sensor exchanges energy by convection with the air, radiation with surrounding surfaces and conduction through supports or leads. A direct view of hot stones or cool glazing can bias an unshielded element away from the undisturbed local air temperature. A screen may reduce radiative exchange, but it also changes ventilation around the sensor and its response.

ISO 17714:2007 defines comparison tests and characteristics for naturally or artificially ventilated meteorological thermometer screens. On 4 September 2026 the ISO record still showed the first edition as published and current after its 2021 confirmation; a later systematic review had closed on 3 September 2026 without a new disposition yet displayed.[10] Its outdoor method is not a sauna protocol, although the underlying radiation–ventilation trade-off is relevant.

Bulky housings can disturb very local flow. Contact with a wall and conduction along a stem introduce other biases. Water casting changes vapour, flow and surface exchange on different time scales; droplets, evaporation from a wetted sensor or condensation can create a sensor transient. A sudden excursion does not establish a uniform dry-bulb-temperature rise throughout the room.

Calibration and uncertainty

Metrological vocabulary separates indication, calibration, adjustment, correction and measurement result. Calibration relates indications to reference values under stated conditions; traceability requires a documented chain whose calibration steps contribute to uncertainty.[11] Display resolution is only one input and should not be reported as accuracy.

The relevant object of calibration may be the complete probe-and-readout channel. NIST’s Industrial Thermometer Calibration Laboratory, for example, compares probes and attached readouts with an ITS-90 calibrated standard platinum resistance thermometer in stirred liquid baths.[12] Its controlled laboratory capabilities do not become the uncertainty of the same channel in stratified sauna air. Calibration points should cover the intended range sufficiently for the use; an ice-point check alone cannot characterise hot-range response.

An uncertainty statement should follow the measurement model. Instrument calibration, readout, repeatability and drift concern the channel; radiation, conduction, lag and wetting concern installation; position and timing concern sampling. JCGM 100:2008 provides the general framework for evaluating and expressing these contributions.[13] Its separately published 2026 amendment addresses nonlinearity in measurement models; it does not supply a sauna budget.[14]

Reporting and interpretation

A reproducible report identifies the purpose, room and heater state, occupancy, water applications, ventilation state, instruments, coordinates, calibration, sampling, processing, synchronisation and uncertainty. Plots should label position and phase. Maxima, minima or contours between measured points require an explicit interpolation or physical model; graphical smoothness is not added spatial resolution.

A temperature record alone does not quantify perceived heat, physiological strain or safety. Radiation, moisture, airflow, contact, duration and individual physiology remain separate. Within Sauna research, comparability comes from disclosed methods and limitations, not from assuming one universal array, mounting height, sampling rate or uncertainty target.

References

  1. ↑ International Organization for Standardization, ISO 7726:2025, Ergonomics of the thermal environment—Instruments for measuring and monitoring physical quantities, third edition, published October 2025, https://www.iso.org/standard/78238.html, accessed 4 September 2026.
  2. ↑ ASHRAE, “Thermal Comfort”, chapter 9 in 2017 ASHRAE Handbook—Fundamentals, https://handbook.ashrae.org/Handbooks/F17/IP/f17_ch09/f17_ch09_ip.aspx, accessed 4 September 2026.
  3. ↑ Hikaru Ishibashi, Riku Tomabechi, Kurumu Nishidate, Nanaho Osaka, Tomoki Shimomura, Shoei Yamada, Junnosuke Okajima and Takuma Kogawa, “Evaluation of radiative absorption effect to estimate mean radiant temperature in environments with high water vapor concentration such as in a sauna”, Building and Environment, volume 243, 2023, article 110684, doi:10.1016/j.buildenv.2023.110684.
  4. ↑ International Electrotechnical Commission, IEC 60751:2022, Industrial platinum resistance thermometers and platinum temperature sensors, third edition, https://webstore.iec.ch/en/publication/63753, accessed 4 September 2026.
  5. ↑ Jonathan Pearce, Richard Rusby, Kazuaki Yamazawa, Stefan Rudtsch, Luca Iacomini, Giuseppina Lopardo, D. Rodney White and Weston L. Tew, Guide on Secondary Thermometry: Industrial Platinum Resistance Thermometers, Consultative Committee for Thermometry, Bureau International des Poids et Mesures, 2022, https://www.bipm.org/documents/20126/41773843/BIPM_CCT_Guide_to_IPRTs.pdf/b3bd8bba-3b0b-ab46-481f-29ceddf7bb31?version=1.1&download=true, accessed 4 September 2026.
  6. ↑ International Electrotechnical Commission, IEC 60584-1:2013, Thermocouples—Part 1: EMF specifications and tolerances, third edition, https://webstore.iec.ch/en/publication/2521, accessed 4 September 2026.
  7. ↑ Erkki Äikäs and Rolf Holmberg, Saunan lämpötilat ja ilmanvaihto [Temperature and ventilation of the Finnish sauna], VTT Research Notes 1431, VTT Technical Research Centre of Finland, Espoo, 1992, 40 pp., ISBN 951-38-4325-4, https://cris.vtt.fi/en/publications/saunan-l%C3%A4mp%C3%B6tilat-ja-ilmanvaihto/, accessed 4 September 2026.
  8. ↑ Youchen Fan, Rolf Holmberg and Jorma Heikkinen, “CFD simulation on the air flow in a sauna”, Building Research & Information, volume 22, number 6, 1994, pp. 307–312, doi:10.1080/09613219408727409.
  9. ↑ Iida Laatikainen-Raussi, Tom Mikkola, Johanna K. Ihalainen and Essi Ahokas, “Temperature and humidity independently influence thermoregulatory responses during Finnish sauna bathing”, Temperature, volume 13, number 3, 2026, pp. 289–299, published online 11 July 2026, doi:10.1080/23328940.2026.2698162.
  10. ↑ International Organization for Standardization, ISO 17714:2007, Meteorology—Air temperature measurements—Test methods for comparing the performance of thermometer shields/screens and defining important characteristics, first edition, published July 2007, current record with systematic review closed 3 September 2026, https://www.iso.org/standard/31498.html, accessed 4 September 2026.
  11. ↑ Joint Committee for Guides in Metrology, International vocabulary of metrology—Basic and general concepts and associated terms, JCGM 200:2012, https://jcgm.bipm.org/vim/en/, accessed 4 September 2026.
  12. ↑ National Institute of Standards and Technology, “Industrial Thermometer Calibrations”, updated 22 December 2025, https://www.nist.gov/pml/sensor-science/thermodynamic-metrology/industrial-thermometer-calibrations, accessed 4 September 2026.
  13. ↑ Joint Committee for Guides in Metrology, Evaluation of measurement data—Guide to the expression of uncertainty in measurement, JCGM 100:2008, corrected 2010, doi:10.59161/JCGM100-2008E.
  14. ↑ Joint Committee for Guides in Metrology, JCGM 100:2008/Amd.1:2026, Evaluation of measurement data—Guide to the expression of uncertainty in measurement—Amendment 1: Nonlinearity in measurement models, 2026, doi:10.59161/PPDI3267.

Template:Sauna technology