Particulate matter from wood burning
Particulate matter from wood burning is the mixture of solid and liquid aerosol particles produced directly by burning wood or formed as combustion vapours cool. In a wood-burning sauna, the intended route for these products is from the stove through the chimney to outdoor air. Measurements in the flue, outdoors and inside the hot room nevertheless describe different points in that route; none can by itself establish the amount inhaled by a bather. Particle mass, particle number, black carbon and chemical composition also measure different attributes of the aerosol.

Research on sauna stoves has found substantial variation between appliances and firing conditions. The most direct evidence comes from a limited number of Finnish stove experiments rather than from surveys of personal exposure. It can therefore identify emission mechanisms and compare tested configurations, but it does not supply a universal emission factor, an ordinary hot-room concentration or a sauna-specific safe dose.
Quantities and size fractions
Particulate matter is not a single substance. PM10, PM2.5 and PM1 are mass fractions obtained using size-selective sampling conventions. Their numerical labels should not be read as perfectly sharp divisions by geometric diameter. ISO 16000-34:2018 addresses general strategies for measuring indoor airborne particles from approximately 1 nanometre to 100 micrometres, including source identification, representative sampling and uncertainty.[1] Its scope is general indoor air; it does not prescribe a sauna limit or a position for a sensor in a sauna.
Mass concentration gives greater weight to larger particles than particle-number concentration. Ultrafine particles can contribute many of the counted particles while adding comparatively little mass. Black carbon, elemental carbon and organic carbon are related analytical quantities, not alternative names for PM2.5. Consequently, a low result for one metric does not guarantee a proportionate result for another. Detailed appliance measurements and emission factors are treated in Particulate emissions from sauna stoves.
Formation and composition
Wood-combustion particles may contain soot or elemental carbon, organic material, inorganic ash salts, metals and particle-bound organic compounds. Lamberg and colleagues compared particles collected from six small-scale combustion situations and found that composition changed markedly with appliance and combustion condition.[2] In their tested conditions, inefficient combustion produced carbon-rich material, whereas some more efficient, hotter conditions increased the relative importance of inorganic ash. This is a conditional pattern, not a rule that hotter burning eliminates particulate emissions.
Semi-volatile material can repartition as exhaust is diluted and cooled. Sampling temperature, dilution and filter conditioning can therefore alter the mass that a method reports. Particle-bound organic matter should also be distinguished from volatile compounds in the gas phase. Carbon monoxide is another gaseous combustion product and is not included in particulate mass. Smoke visibility and odour may reveal plume contact, but neither is a quantitative PM2.5 measurement.
Evidence from sauna-stove tests
Tissari and colleagues tested ten commercially available Finnish sauna-stove models under a controlled protocol. They found nine-fold variation in measured PM1 mass concentration between models when dry birch was used, together with still larger variation in some chemical measures.[3] The work demonstrates appliance-specific behaviour within its sample; it does not show the distribution of emissions from all installed stoves.
Emissions also vary over a batch. Ignition, rapid fuel decomposition, flaming, char burning and ash release do not produce identical particles. Earlier experiments with masonry heaters and two sauna stoves found that inadequate air during rapid pyrolysis and increased ash release at high temperature could each accompany high emissions.[4] Attributing every particle peak to smouldering would therefore omit a separate ash-related mechanism.
Fuel moisture, log size, load, ignition and combustion-air supply belong with any numerical comparison. In the ten-stove experiment, changing moisture did not shift PM1, particle number, black carbon, carbon monoxide and polycyclic aromatic hydrocarbons in a common direction.[3] Its limited comparisons of wood species and bark likewise do not provide a general ranking of Sauna firewood.
Combustion-air distribution is partly an appliance-design question. Väätäinen and colleagues reported lower PM1, black-carbon, organic gaseous carbon and carbon-monoxide emissions after introducing secondary-air staging in one experimental stove, with further changes when primary air was restricted and redistributed.[5] The pollutant-specific results apply to that engineered configuration. Altering the air paths of an installed stove can affect draught, efficiency and fire safety and is not an inference warranted by the experiment.
From emission to exposure
A flue emission factor is commonly normalised by dry fuel mass or energy. Outdoor and indoor concentrations are expressed per volume of air, while personal exposure combines concentration with where and for how long a person is present. Moving between those quantities requires exhaust-flow, dispersion, infiltration and occupancy information.
Thus a chimney measurement cannot be treated as a hot-room reading. Smoke that escapes its intended flue route or an outdoor plume that enters a building can affect occupied air, but the pathway and concentration need to be established in the particular setting. The mixed plume and its dispersion fall within Wood smoke from saunas, while occupied-room assessment belongs to Air quality monitoring in a sauna and Indoor air quality in a sauna. General room ventilation may dilute material already indoors, but it is not a remedy for a defective flue path. Pressure differences and air movement can also interact with chimney draught.
Emission inventories operate at a wider scale again. Savolahti and colleagues modelled Finnish residential wood combustion and found sauna stoves to be the largest contributor within the appliance stock used in their PM2.5 and black-carbon estimates.[6] That national result depends on its model years, activity data and Finnish appliance mix. It is neither a worldwide share nor an estimate of an individual sauna visit.
Measurement
Filter gravimetry accumulates particulate mass over a sampling interval. Optical and electrical instruments can follow shorter peaks, but their signals depend on particle size, shape, refractive index and, for some methods, humidity. ISO 16000-37:2019 specifies a filter-and-impactor reference principle for indoor PM2.5 mass concentration and procedures for supplementary high-time-resolution instruments.[7] It does not establish that a consumer monitor is equivalent to the reference method or that an instrument can tolerate sauna heat and humidity.
A reproducible report identifies whether sampling took place in raw flue gas, diluted exhaust, outdoor air or occupied space. It also records the size fraction, mass or number metric, averaging period, flow and dilution conditions, instrument, calibration and uncertainty. Condensation in a cooler sampling line can change semi-volatile material, while humidity can interfere with some particle sensors. Results obtained with unlike boundaries or methods should not be combined without a demonstrated conversion.
Health significance
The WHO's 2021 air-quality guidelines evaluate evidence that population exposure to PM2.5 and PM10 is associated with cardiovascular, respiratory and other adverse outcomes.[8] Their annual and 24-hour values are health-based ambient recommendations with stated averaging periods. They are not limits for raw stove exhaust or a brief sauna session. WHO gives good-practice statements, rather than separate numerical guideline levels, for black or elemental carbon and ultrafine particles.
Controlled human evidence on wood smoke is heterogeneous. Schwartz, Bølling and Carlsten identified 22 publications arising from 12 controlled studies, with wide differences in combustion source, concentration, duration, exercise and measured endpoints; they judged general conclusions about acute health effects premature.[9] Those studies were not trials of sauna-stove exposure.
Laboratory toxicology answers a still narrower question. Tapanainen and colleagues exposed cultured mouse macrophages and human bronchial epithelial cells to collected PM1 from four wood-burning appliances. Particles from an inefficient sauna-stove phase produced the strongest cytotoxic and genotoxic responses in those assays.[10] A response at an administered cell-culture dose does not quantify disease risk or define a safe bathing duration.
Source control and product scope
Reducing emissions begins with the complete combustion system: a compatible appliance and flue, appropriate combustion-air provision, fuel and operation specified for the stove, and maintenance of the approved installation. Meeting a product standard does not imply zero emissions or describe every installation. It also does not make a simple electric-versus-wood comparison an assessment of exposure, since source, electricity generation, ventilation and use define different boundaries.
The cited Dutch adoption of EN 16510-2-10:2025 is current and covers specified hand-fuelled, multi-firing sauna stoves that burn natural wood logs.[11] Its public scope excludes, among other configurations, single-firing heat-storage stoves with direct stone heating, mechanically fed stoves and appliances with electrical connections. Adoption and application must be checked for the relevant jurisdiction; broader product context belongs to Wood-burning appliance standards.
Commission Regulation (EU) 2015/1185 expressly excludes sauna stoves from that regulation's ecodesign requirements for solid-fuel local space heaters.[12] The exclusion concerns that measure only; it is not an exemption from other product, installation, fire or air-quality rules. Outdoor plume and neighbour issues are treated separately under Smoke nuisance from a sauna and Noise and smoke nuisance rules.
References
- ↑ ISO, ISO 16000-34:2018, Indoor air — Part 34: Strategies for the measurement of airborne particles, edition 1, August 2018, confirmed 2023, https://www.iso.org/standard/64069.html, accessed 4 September 2026.
- ↑ Heikki Lamberg, Kati Nuutinen, Jarkko Tissari, Jarno Ruusunen, Pasi Yli-Pirilä, Olli Sippula, Maija Tapanainen, Pasi Jalava, Ulla Makkonen, Kimmo Teinilä, Karri Saarnio, Risto Hillamo, Maija-Riitta Hirvonen and Jorma Jokiniemi, “Physicochemical characterization of fine particles from small-scale wood combustion”, Atmospheric Environment, volume 45, issue 40, 2011, pp. 7635–7643. doi:10.1016/j.atmosenv.2011.02.072
- ↑ 3.0 3.1 Jarkko Tissari, Sampsa Väätäinen, Jani Leskinen, Mikko Savolahti, Heikki Lamberg, Miika Kortelainen, Niko Karvosenoja and Olli Sippula, “Fine Particle Emissions from Sauna Stoves: Effects of Combustion Appliance and Fuel, and Implications for the Finnish Emission Inventory”, Atmosphere, volume 10, issue 12, 2019, article 775. doi:10.3390/atmos10120775
- ↑ Jarkko Tissari, Kati Hytönen, Olli Sippula and Jorma Jokiniemi, “The effects of operating conditions on emissions from masonry heaters and sauna stoves”, Biomass and Bioenergy, volume 33, issue 3, 2009, pp. 513–520. doi:10.1016/j.biombioe.2008.08.009
- ↑ Sampsa Väätäinen, Jani Leskinen, Heikki Lamberg, Hanna Koponen, Miika Kortelainen, Olli Sippula and Jarkko Tissari, “The effects of air staging and combustion air control on black carbon and other particulate and gaseous emissions from a sauna stove”, Fuel, volume 331, 2023, article 125769. doi:10.1016/j.fuel.2022.125769
- ↑ Mikko Savolahti, Niko Karvosenoja, Jarkko Tissari, Kaarle Kupiainen, Olli Sippula and Jorma Jokiniemi, “Black carbon and fine particle emissions in Finnish residential wood combustion: Emission projections, reduction measures and the impact of combustion practices”, Atmospheric Environment, volume 140, 2016, pp. 495–505. doi:10.1016/j.atmosenv.2016.06.023
- ↑ ISO, ISO 16000-37:2019, Indoor air — Part 37: Measurement of PM2,5 mass concentration, edition 1, February 2019, confirmed 2024, https://www.iso.org/standard/66283.html, accessed 4 September 2026.
- ↑ WHO, WHO global air quality guidelines: particulate matter (PM2.5 and PM10), ozone, nitrogen dioxide, sulfur dioxide and carbon monoxide, Geneva, 22 September 2021, ISBN 978-92-4-003422-8, https://www.who.int/publications/i/item/9789240034228, accessed 4 September 2026.
- ↑ Carley Schwartz, Anette Kocbach Bølling and Christopher Carlsten, “Controlled human exposures to wood smoke: a synthesis of the evidence”, Particle and Fibre Toxicology, volume 17, issue 1, 2020, article 49. doi:10.1186/s12989-020-00375-x
- ↑ Maija Tapanainen, Pasi I. Jalava, Jorma Mäki-Paakkanen, Pasi Hakulinen, Heikki Lamberg, Jarno Ruusunen, Jarkko Tissari, Jorma Jokiniemi and Maija-Riitta Hirvonen, “Efficiency of log wood combustion affects the toxicological and chemical properties of emission particles”, Inhalation Toxicology, volume 24, issue 6, 2012, pp. 343–355. doi:10.3109/08958378.2012.671858
- ↑ European Committee for Standardization, EN 16510-2-10:2025, Residential solid fuel burning appliances — Multi-firing sauna stoves fired by natural wood logs — Requirements and test methods, NEN national-adoption record, published 1 June 2025, https://www.nen.nl/en/nen-en-16510-2-10-2025-en-339130, accessed 4 September 2026.
- ↑ European Commission, Commission Regulation (EU) 2015/1185 of 24 April 2015 implementing Directive 2009/125/EC with regard to ecodesign requirements for solid fuel local space heaters, Article 1(2)(f), https://eur-lex.europa.eu/legal-content/EN/ALL/?uri=CELEX:32015R1185, accessed 4 September 2026.
