Moisture content of firewood
Moisture content of firewood expresses the mass of water in a wood sample relative either to its total as-received mass or to its oven-dry wood mass. These are the wet-basis and dry-basis conventions respectively. They give different numerical percentages for the same material, so an interpretable result identifies the basis, sample and measurement method.
Fuel specifications commonly use wet basis, while wood-science sources often use dry basis. Moisture is only one property of sauna firewood: a dry log can still be treated, contaminated, wrongly sized or excluded by the stove instructions.
Bases of expression
Wet-basis moisture divides water mass by total mass—the sum of water and dry wood—and expresses the ratio as a percentage. Dry basis divides the same water mass by oven-dry wood mass. A dry-basis value can exceed 100 per cent when the water weighs more than the dry wood; wet basis cannot exceed 100 per cent by definition.[1]
The two conventions can be converted mathematically only after the original basis is certain. Relabelling an unexplained number or assuming that a seller and a scientific paper used the same convention creates a larger interpretive error than ordinary rounding. Reports should retain the original basis and method rather than convert merely to make unlike data appear comparable.
ISO 18134-1:2022 specifies total-mass, or wet-basis, reporting for as-received solid-biofuel samples.[2] The USDA Wood Handbook, by contrast, describes many wood-material relationships using oven-dry mass as the denominator.[3] A fuel label and a wood-property table should not be compared until this denominator is known.
Reference methods
Oven determination derives moisture from mass lost while a prepared specimen is dried under defined conditions. ISO 18134-1 describes a reference method for uses requiring high precision. ISO 18134-2:2024 provides a simplified oven method for routine control where the highest precision is unnecessary, while retaining wet-basis reporting.[4] Their public descriptions note that a small amount of volatile organic material can be lost during drying and is disregarded relative to the overall result. Neither paid standard is reproduced here as a household procedure.
ASTM D4442-20(2025) distinguishes its primary oven-drying method for wood and wood-based material from a secondary method of lower precision. Its public text also warns that knots, sapwood and heartwood affect representativeness and that volatile non-wood chemicals can bias the measured mass loss.[5] Reference-method accuracy for one specimen does not make that specimen representative of a delivery.
Sampling
Moisture can vary between logs and within one piece, including between surface and core and between sapwood and heartwood. Selecting, splitting and preparing a sample is therefore a separate problem from determining its moisture.
ISO 18135:2017 describes sampling plans for materials including stockpiles, deliveries, roundwood and pieces larger than 200 mm. The standard remained published on 4 September 2026 but had entered the “to be revised” stage.[6] The breadth of that scope illustrates why one convenient log cannot automatically describe a stack. Sampling uncertainty and measurement uncertainty should not be conflated.
The decision being made determines the needed evidence. A quick screen before firing, checking compliance with a model instruction and certifying a commercial shipment are different tasks. A result close to a threshold is particularly sensitive to basis, sample location, method and instrument limitations.
Handheld electrical meters
An electrical meter estimates local moisture from an electrical property correlated with water content; it does not directly balance the water mass of a whole load. Instrument design, calibration, species, wood temperature, grain direction, electrode contact and probe position can influence a reading. Corrections and insertion geometry must follow the identified meter rather than an unsourced universal table.

The US Environmental Protection Agency's consumer guidance recommends splitting a log, measuring the newly exposed interior face, placing probes in the stated grain direction and following the meter instructions.[7] This is a practical screen, not the ISO reference method or certification of an entire stock.
Price-Allison and colleagues compared a commercial probe with oven results for beech and spruce logs over a wide moisture range. The probe substantially underestimated some values, and moisture was not uniform within individual logs.[8] The result concerns one device and protocol in a residential-stove study. It demonstrates possible disagreement rather than a correction applicable to every meter.
Storage and environmental exchange

Splitting, piece thickness, species, wood structure, air movement and surrounding temperature and humidity all influence drying. Wood exchanges moisture with the surrounding air and approaches an equilibrium associated with temperature and relative humidity.[3] Rain and damp-ground contact can reverse earlier drying. Calendar age consequently does not establish present moisture.
UK guidance treats colour, cracks, loosened bark, sound and relative weight as indicators rather than direct percentage measurements.[9] Storage should limit precipitation and ground wetting while permitting ventilation. A sauna wood rack or firewood basket does not preserve a certified value, and its location must respect safety distances.
Instructions and legal thresholds
The figure 20 per cent occurs in sources with different scopes. Narvi's March 2025 manual requires moisture below 20 per cent for its Black 16, 20, 24 and 20 VS stoves.[10] It is a model-specific condition, not a rule for every sauna heater.
England's Air Quality (Domestic Solid Fuels Standards) Regulations 2020 set a maximum of 20 per cent for wood sold in quantities below two cubic metres within the specified certification scheme.[11] That is a jurisdictional sales threshold, not a thermodynamic line between safe and unsafe combustion. Similar numbers should not be merged without preserving their basis, test method and legal or product context. Nor does the evidence show that the lowest attainable moisture is best for every appliance.
Combustion evidence
Water absorbs heat while warming and evaporating, changing combustion timing and temperature history. The consequences need not point in one direction for every pollutant. In a Finnish campaign, two sauna stoves were compared using wood at about 11 and 18 per cent moisture. Burns with the 18-per-cent fuel lasted longer and produced lower measured temperatures in the flue and sauna room. They yielded higher carbon-monoxide and particle-number concentrations but lower PM1 mass, polycyclic aromatic hydrocarbons and black carbon.[12]
This two-model comparison is not a continuous response curve for all stoves. A separate experiment in one domestic stove found moisture-related changes in both the quantity and character of emissions from beech fuel.[13] It supports moisture as an operating variable but does not transfer an effect size to sauna stoves.
Moisture alone cannot diagnose the flue, chimney, air setting or appliance. Detailed emissions evidence belongs under Particulate emissions from sauna stoves, Carbon monoxide in a sauna, Wood smoke from saunas and Smoke nuisance from a sauna. A spark arrestor does not alter the moisture result, and combustion residue follows the separate ash-management chain.
Interpretation
A moisture value does not identify species, dimensions, chemical treatment or contamination. Those properties can independently determine whether fuel is acceptable. The defensible interpretation states what was sampled, how it was prepared, which basis and method were used, and which product or legal decision the number informs. Without that context, extra decimal places do not make a reading more meaningful.
For operation of a wood-burning sauna, the measurement is therefore an input rather than a verdict. A pass against one threshold does not approve the log's provenance or loading, while a failed screen should be resolved under the controlling stove or sales procedure rather than by selecting a more favourable surface point.
References
- ↑ William T. Simpson (ed.), Dry Kiln Operator's Manual, USDA Forest Service, Forest Products Laboratory, Agriculture Handbook 188, 1991, chapter 1, https://research.fs.usda.gov/treesearch/7164, accessed 4 September 2026.
- ↑ International Organization for Standardization, ISO 18134-1:2022, Solid biofuels — Determination of moisture content — Part 1: Reference method, second edition, August 2022, https://www.iso.org/standard/83191.html, accessed 4 September 2026.
- ↑ 3.0 3.1 USDA Forest Products Laboratory, Wood Handbook: Wood as an Engineering Material, General Technical Report FPL-GTR-282, 2021, chapter 4, https://www.fpl.fs.usda.gov/documnts/fplgtr/fplgtr282/fpl_gtr282.pdf, accessed 4 September 2026.
- ↑ International Organization for Standardization, ISO 18134-2:2024, Solid biofuels — Determination of moisture content — Part 2: Simplified method, third edition, March 2024, https://www.iso.org/standard/86024.html, accessed 4 September 2026.
- ↑ ASTM International, ASTM D4442-20(2025), Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials, active 1 September 2025. doi:10.1520/D4442-20R25.
- ↑ International Organization for Standardization, ISO 18135:2017, Solid biofuels — Sampling, first edition, confirmed 2022 and at “to be revised” stage since 30 June 2026, https://www.iso.org/standard/66481.html, accessed 4 September 2026.
- ↑ US Environmental Protection Agency, Test Your Wood with a Moisture Meter, EPA-456/F-20-003, 2020, https://nepis.epa.gov/Exe/ZyPURL.cgi?Dockey=P1010E3L.TXT, accessed 4 September 2026.
- ↑ A. Price-Allison, A. R. Lea-Langton, E. J. S. Mitchell, B. Gudka, J. M. Jones, P. E. Mason and A. Williams, “Emissions performance of high moisture wood fuels burned in a residential stove”, Fuel, volume 239, 2019, pp. 1038–1045. doi:10.1016/j.fuel.2018.11.090.
- ↑ UK Department for Environment, Food & Rural Affairs, “Burn Better, Breathe Better”, https://uk-air.defra.gov.uk/library/burnbetter/, accessed 4 September 2026.
- ↑ Narvi Oy, Narvi Black 16 / 20 / 24 / 20 VS: Installation and instruction manual, version 03/2025, sections 4.1–4.4, https://narvi.fi/mediatiedostot/manual-narvi-black/, accessed 4 September 2026.
- ↑ United Kingdom, Air Quality (Domestic Solid Fuels Standards) (England) Regulations 2020, SI 2020/1095, https://www.legislation.gov.uk/uksi/2020/1095/pdfs/uksi_20201095_en.pdf, accessed 4 September 2026.
- ↑ Jarkko Tissari, Sampsa Väätäinen, Jani Leskinen, Mikko Savolahti, Heikki Lamberg, Miika Kortelainen, Niko Karvosenoja and Olli Sippula, “Fine Particle Emissions from Sauna Stoves: Effects of Combustion Appliance and Fuel, and Implications for the Finnish Emission Inventory”, Atmosphere, volume 10, issue 12, 2019, article 775. doi:10.3390/atmos10120775.
- ↑ Andrew Price-Allison, Patrick E. Mason, Jenny M. Jones, Eric K. Barimah, Gin Jose, Aaron E. Brown, Andrew B. Ross and Alan Williams, “The Impact of Fuelwood Moisture Content on the Emission of Gaseous and Particulate Pollutants from a Wood Stove”, Combustion Science and Technology, volume 195, issue 1, 2023, pp. 133–152. doi:10.1080/00102202.2021.1938559.
